DHI, DKI, DKO, DPHI, series complete with fully encapsulated class H coil flow up to 1000L/MIN
Pressure up to 350 Bar
Specific Version are available for hazardous environment and for marine or military applications.
Conventional Valves
Subplate, threaded port or flange mounting according to cetop, ISO, relief, sequence, unloading and combined pressure controls, throttle and pressure compensated flow control valve, direct and pilot operated check valves. flow up to 400L/MIN.
Proportional Valve
Spool type or in cartridges type
ZO series solenoid – NG03 to NG 10 suitable for open and close loop application.
ZJ series for lower power (low) and high dynamic (150Hz). Improve hydraulic performance and reliability.
Integrated electronic driver available
Flow up to 1200L/MIN, pressure up to 350 Bar
Modular Valves
ISO, cetop 03, 05, 07, 08, subplate relief, sequence, reducing check, flow control valves and pressure compensators, flow up to 300L/MIN.
Cartridge Valve
ISO, or Atos standard, NG06 through NG80, pressure flow and directional control, on / off and proportional, flow up to 4000L/MIN.
Pressure reducing, relief, counterbalance, sequence and unloading valves
Inline or manifold mounted
3/4″ to 1 1/4″ size
Flow to 90 GPM
Pressure to 3000 PSI (207 Bar)
Colour flow control valves
Inline mounted flow, check needle, Gauge isolator and snubber valves
Pressure compensated or non-compensated flow controls
Size 1/8″ through 2″
Port NPTF, SAE and BSP
Pressure to 5000 PSI (350 bar)
Flow to 150 GPM
Available in brass or steel
Servovalve
E062 through D079-200 series complete with mechanical / electrical feedback
Flow up to 750L/MIN
Maximum pressure up to 350 BAR
Proportional Valve
D660 series – Integrated electrical feedback 16-1500L/MIN
D650 series – flow and pressure (PQ) integrated EPB 23-800 L/MIN
Maximum pressure up to 350 bar
Servo Actuatory
M850 series – long stroke linear servo actuators
A085 series – short stroke servo actuators
A084 series – rotary servo drives
Moog products provides precise control of motion, velocity or force so important to the proper operation of a wide variety of industrial machinery and aerospace. For example Blow / injection mounding flight simulator, material testing, military aircraft, etc.
Oilpath
Mono block type mobile hydraulic control valve
OP 10 series – 45 L/MIN and op 20 series – 80L/MIN
Pressure up to 3000 PSI
Provision for closed circuit or power beyond
Maximum spool available up to 4 spools for OP10 series and 5 spool for OP20 series
Control option : lever, cable, or Pneumatic control
Counterbalance Valve
Sun Hydraulics counterbalance cartridges, modulating devices for load holding and motion control, can be directly integrated into your actuator or applied using manifolds with many mounting options.
Offer hose break protection
Prevent loads from drifting
Control overrunning loads
Provide overcenter load control
Protect against pressure due to thermal expansion
Are physically interchangeable with pilot-to-open check cartridges (same number of ports, same cavities, same flow path for a given frame size)
Adjustable Pressure-Compensated Flow
Controls
Sun Hydraulics reducing/relieving cartridges are available in different versions and can be conveniently applied using many mounting options.
Functionally interchangeable with one another (same flow path, same cavity for a given frame size)
Five sizes, flow rates up to 80 gpm (320 L/min.)
Fully adjustable up to and including 4500 psi (315 bar) with inlet pressures up to 5000 psi (350 bar) (except air piloted versions)
Reducing/relieving cartridges are offered in both three- and four-port configurations
Pilot-to-Open Check Valves
Sun Hydraulics’ pilot-to-open check cartridges are non-modulating, on-off devices used for holding a load or actuator in position. Sun pilot-to-open check cartridges can be directly integrated into your actuator or applied using manifolds with many mounting options.
Offer protection against hose breaks
Positively lock pressurized loads
Are available in non-vented (3-port) and vented (3- and 4-port) versions
Are physically interchangeable with counterbalance cartridges (same number of ports, same cavities, same flow path for a given frame size).
Reducing Valves
Sun Hydraulics reducing cartridges are available in variety of configurations and can be conveniently applied using many mounting options.
Functionally interchangeable with reducing/relieving cartridges (same flow path, same cavity for a given frame size)
Five sizes, flow rates up to 80 gpm (320 L/min.)
Fully adjustable up to and including 4500 psi (315 bar) with inlet pressures up to 5000 psi (350 bar), except air piloted versions
Sequence Valve
Sun Hydraulics` sequence cartridges are similar to relief cartridges except the pilot is separately drained so that valve setting is not affected by pressure in the outlet port. Sun sequence cartridges can be conveniently applied using many mounting options.
Functionally interchangeable with one another (same flow path, same cavity for a given frame size)
Offered in five sizes with flow rates up to 120 gpm (480 L/min.)
Fully adjustable over a wide range of operating pressures up to and including 5000 psi (350 bar) (6000 psi (420 bar) intermittent) (except air piloted versions)
Relief Valves
Sun Hydraulics offers many different pressure limiting and pressure regulating relief cartridges that can be conveniently applied using many mouting options.
Available in 2-, 3-, and 4-ports
Functionally interchangeable (except pilot only versions) with valves with the same number of ports (same flow path, same cavity for a given frame size)
Five sizes, flow rates up to 200 gpm (800 L/min.)
Versions are available with an integral pilot control cavity that accepts Sun’s T-8A pilot pressure controls – electro-proportional or pneumatic
Fully adjustable up to and including 5000 psi (350 bar) (6000 psi [420 bar] intermittent), except air piloted versions
Directional Control Valves
Directional valves are either manually or hydraulically actuated spools. Manually-actuated valves are available as 2-way, 3-way, and 4-way valves, and are used either for flow or direction control.
Flow Control Valves
Used to limit or regulate flow. 3 basic type:
two-ported valves that maintain a constant flow rate from 1 to 2 regardless of load pressure changes in the circuit downstream of 2
When the valve is functioning as a divider, it will divide input flow from 3 to the two outputs at 2 and 4 according to a preset ratio.
When the valve is functioning as a combiner, it will combine the flow from the two inputs from 2 and 4 into one output at 3.
